frame

For my current build ( ‘79 Super Sport resto-mod ), I would like to limit the steering turning by about 1/2” on each side — this to allow enough clearance between controls mounted on the clip-on bars, and the gas tank, and prevent contact. Any suggestions out there ? Has anyone done or tried...

The 1977 model has a hard to find 17 inch rear wheel. Will an 18 slide in without modification? The stock 17 is looking pretty good, ready for powdercoating but I may want to go higher end as the bike is in great restoerable shape.

Restoring a 1977 CB750K on a budget. Wheel bearings are running $30-$50 on line (6304LU bearing) but I can get the 6304 2RS at Princess Auto for $7, same dimensions, 2RS indicating they are sealed on both sides. Is anyone using these bearings? They sure look and feel good

I have a 1980 CB750C 32,000 miles on the spedo. I Purchased the bike used several years ago and finally got it running last year. The motor runs good. The bike was then parked for several years prior to me purchasing it. The seller did not know the history of the bike since it was driven by a...

Your previous message Hi, am I right in thinking that a 1976 cb750F1 and K use the same front wheels? Are there any other 750 models where front wheels are interchangeable with the 76 F1 ? (spoked). Thanks

I need help please ,i just purchased a Honda F2 from 1977 F2. Can someone please tell me and identify the frame and the engine this bike? The engine number is CB750GE1007834 and the frame number is CB750G1002368 . Any help would be greatly appreciated. Thank you

Hello all, I am starting a Honda chopper project. I can't find much help on the world wide web unless I'm not looking in the right location. I need help with options of what to do with the frame. I'm not sure if I want to modify the frame or get an already modified one. Any help with web sites...

Still looking for some OE handlebars for my 81 CB750F, or a aftermarket set as close to the original ones that would have come with the bike. I don't have the factory ones to compare and not sure of the measurement for OE bars Thanks

Hey guys. Building a 76 cb750f in to a cafe racer. I’m trying to keep as much of the vintage look as possible and would like to add a dual disc set up. I know the 77 & 78 came factory as that. Can the 77 & 78 forks be directly swapped in to a 76 chassis? If they are, can I still run the factory...

As I’m looking at adding new rear shocks to my trike project curious as to any recommendations for rear shocks anything different than stock? Thanks

I've recently purchased a '79 CB750L anniversary bike. I will be picking it up next month. I live in my motor home and I will be loading it on a flat car hauler with my Jeep. I need a couple of dimensions. I need to know the total length of the bike from the front of the front tire to the...

I've been looking for a rear rim (spoke)for my 81 cb750k forever. The chrome is pretty roached along with the spokes. The honda # is 42701-425-771. Apparently, this rim has not been manufactured for quite some time so looking for a replacement part# that is current or if anyone has any ideas...

Hi. My name is Bill ( Bartster). I am new to this forum but look forward on getting advice for my project. I have a body ( cafe ) for a 1972 750CB. Also have a cafe fairing off a 1974 BMW R90S. Would like to know if there is any frame changes between 1972 and 1982. Want to eliminate the gas...

I am installing new fork tubes and when I disassembled them the narrow spacer fell and turned over. Does anyone know which way round the large chamfer has to point towards?

Does any one know if handlebar controls from a cb 450 are the same as 750 for 1971 ,I am having troub finding for my 750 thanks jerry

In an effort to avoid repeating a question that has been discussed-to-death, I looked through the Forum to see if I could find posts on this issue. I was unsuccessful. If it's here, please point me in the right direction. If it hasn't been previously discussed (and I find that hard to...

Has anyone swapped an rc42 swing arm onto an 80’s DOHC 750f? How close are the measurements? Can anyone tell me the dimensions of the RC42 swing arm? Or suggest a swing arm that doesn’t require any serious fabrication? Looking to upgrade my rear swing arm with a square frame and retain the...

I see where people use a grease gun to remove stuck pistons in calipers my question is do they put a grease fitting in the line or the bleeder hole and what what do they use in the other hole to seal it. what sizes fit the holes mine is a 1998 750F supersport

Thinking about replacing the old shocks and wondered if any of you had experience with the stock design sets from VIntage 750 ? https://www.vintagecb750.com/products/3/suspension-wheel They look at different than the stock ones that I have on the bike as shown.

Handlebars, throttle, and throttle cables any help bought motorcycle chopped but wrong Handlebars and throttle

Is it possible to rebuild the rear shocks on the '79 CB750K? I think I read somewhere that they are gas filled too? Can anyone please explain or direct me to any resources on how the ones on the 750 work? Thanks.

I have a 78 cb 750 and have been looking at lowering the front. I know the 77-78 sit about 2" higher than earlier models due to the upper triple tree and tube length. Question I have is can you all show me your front stance and measure top of top triple tree to bottom of fork? I'm trying to...

What's up Guy's? I'm New to the Page, I have a 74 that came with Tank and Plastic's from a 78. It has the Pumper Carb's from a 78 as well. Anyway's I also have an 84 CB-650 with no Title and I was wondering if it was possible to mount the Twin Disk front Breaks it has on my 750's 19" Lester Mag...

I have a 1978 750k barn find I am updating. I am going to a 1980 cb750c swing arm because its about 1.5" - 2" longer and looks completely factory. My rear wheel is a simple bolt on but some modification needs to be done to bolt up. The pivot is .5" too long which is and easy fix. The bearings...

Hello, I have a 1982 cb 750f. I have a strange thing happening. I just bought this bike so i have no history of this. Under breaking and under hard acceleration i feel a twitch or a movement in the back end. Just for a split second and goes away. Feels almost as the back tire is slipping. It...

I am looking for a rear swingarm , chain guard and brake rod for a 1974 cb750k that will accept a bolt at the end to enable the rider to remove the rear chain without removing the rim

So I am redoing both master cylinders on my 77 F2 The rear is absolutely shot and the caliper aint great either . All three calipers were seized , but I was able to free them without much trouble . The rear brakes are just covered in corrosion and the piston in the master cylinder will not come...

I am looking for a K0 frame. If you have one or know someone that might have one, please let me know. I came across a 1970 K0 engine case that had been stored for 35 years and need a frame to go with it. Thanks, Cedric

does anyone here know the correct sprocket sizes for a 1979 JDM 750FZ { five nut rear sprocket }

I've had some bad luck with one of my fork seals consistently leaking and wanted to get the opinion of others. Take a look at the following pictures and please let me know if anything obvious stands out that could potentially cause a fork to leak: I feel like the problem likely has to do with...