-
Enter the September CB750 Supply gift certificate giveaway! It's easy... Click here, post something, and you're entered into the drawing!
-
-
hinksy replied to the thread Paintwork and the engine have been done , now the build begins.So close now , just have to figure out the technodigicals . Am I right in guessing the US starter cuts out the headlight when you press... -
-
hinksy replied to the thread Paintwork and the engine have been done , now the build begins.All that glitters aint gold mate , some bits I am not so happy with but cannot find a replacement . Should have it all together this...
-
-
hinksy replied to the thread Honda CB750 Wiring Diagrams.Doing the wiring harness right now and I hope this helps some of the euro/uk/aussies on here . Two f series diagrams and two k7`s
-
-
hinksy replied to the thread 1977 CB750F rear caliper.While you are waiting for the grease nipple , soke the caliper /pistons in penetrant . They could be very badly corroded and might need...
-
-
hinksy replied to the thread Paintwork and the engine have been done , now the build begins.What a pain trying to run all of the cables and wiring . Will have a go at connecting all of the wiring in the headlight this weekend ...
-
-
hinksy replied to the thread Paintwork and the engine have been done , now the build begins.Sourced a righthand switch with the correct aussie switches from the father land for a good price . The F2 has the wiring outside of the...
-
-
hinksy replied to the thread Paintwork and the engine have been done , now the build begins.A little play this arvo , put the 530 chain on and thought it would look smaller , and just sat the aircleaner on the carbs to keep any...
-
-
hinksy replied to the thread Paintwork and the engine have been done , now the build begins.Starting to look like a bike now , but still lots to do
-
-
hinksy replied to the thread Paintwork and the engine have been done , now the build begins.Made a blinker stem for my headlight brackets today . Not quite standard and a fraction wider , but the best I can do with what I have
-
-
hinksy replied to the thread Paintwork and the engine have been done , now the build begins.It was a decal that I sourced from Vintagecb.com , they are $133 at the moment if you are interested
-
hinksy replied to the thread Paintwork and the engine have been done , now the build begins.Bench synced and set the float heights on the carbs , then fitted them . Was going over the brakes and setting them up when I noticed...
-
-
hinksy replied to the thread Paintwork and the engine have been done , now the build begins.Put in the wiring harness , rectifier , regulater , fuse block and rear inner guard . Got my switch gear back from being rebuilt also ...
-
-
hinksy replied to the thread Paintwork and the engine have been done , now the build begins.Spent the afternoon playing with the bike . Put on the guage cluster , intake rubbers , rear brake master cylinder and the...
-
-
hinksy replied to the thread Paintwork and the engine have been done , now the build begins.Hooked up the crankcase breather after spending weeks trying to find it , it had dropped behind a shelf , so was very hard to find . Put...
-
-
I am selling a matching pair of headlight brackets for the K7-8 model honda . They were bought by me hoping that they would fit an F2 ...
-
-
hinksy replied to the thread Paintwork and the engine have been done , now the build begins.So I go to lay out the wiring harness and start plugging in the stator and rectifier and starter relay and so forth , and wouldnt you...
-
-
hinksy replied to the thread Paintwork and the engine have been done , now the build begins.Got a bit done today with new tyres , wheel bearings/seals , battery tray , tool tray and a bit of paint on the front forks
-
-
hinksy replied to the thread Paintwork and the engine have been done , now the build begins.Tapered steering head bearings , done
-
-
I need to get a new chain for my 77 F2 . A new o-ring 630 will cost me the same as a new 530 o-ring and sprockets . So a no brainer...
-
hinksy replied to the thread Paintwork and the engine have been done , now the build begins.And the jigsaw begins . At least when it is this stripped , it is easy to do by yourself . Bit by bit and it`ll be a goer . I do have a...
-
-
hinksy replied to the thread Paintwork and the engine have been done , now the build begins.Glad thats over , Flew to melbourne from toonsville . Hired a car . drove 3hrs and picked up the motor . then drove 2.5 days home over...
-
-
-
Loading…
-
Loading…
-
Loading…
-
Loading…
![IMG_20240825_164036[1].jpg](/data/attachments/15/15362-fa46583408277b89cd0e87240cab03ab.jpg)
![IMG_20240825_164112[1].jpg](/data/attachments/15/15363-aae16750186a487505b97b9b930c71d5.jpg)
![IMG_20240714_145413[1].jpg](/data/attachments/15/15090-221c395324d5c51c1c009510e0f893e0.jpg)
![IMG_20240714_145240[1].jpg](/data/attachments/15/15091-cfcc083bbb8208758ab0380edc26ef16.jpg)
![IMG_20240714_145344[1].jpg](/data/attachments/15/15092-90f63a52db3f6db4ac41c856cdab279f.jpg)
![IMG_20240707_093557[1].jpg](/data/attachments/15/15049-31cb192efbad5ae448df26bf7b73c7b5.jpg)
![IMG_20240704_143117[1].jpg](/data/attachments/14/14981-e1c63eb215b32692efb1278200412a1e.jpg)
![IMG_20240703_161805[1].jpg](/data/attachments/14/14980-006e88878a2dd4e4b4733bac39b31d90.jpg)
![IMG_20240628_124402[1].jpg](/data/attachments/14/14947-cc3c2be9af9eaeb5a81991ce91bd21ce.jpg)
![IMG_20240628_124727[1].jpg](/data/attachments/14/14948-9d47f3ae43f4326a46486cd3587cf808.jpg)
![IMG_20240628_124749[1].jpg](/data/attachments/14/14949-1594a067e1c97fef57804a8ae0a6f22d.jpg)
![IMG_20240628_124411[1].jpg](/data/attachments/14/14950-22775a6c004b77e8ddd026b956989153.jpg)