clutch

Ok,it’s been at least a year since I have had my bike running. Just cleaned carbs. I was going to take it for a test, but the clutch is not disengaging. When i have clutch in and put into 1st, it just lurches forward and kills. Clutch not working. It’s like popping the clutch at idle. This has...

Just got this bike running after 5 years of sitting. Cleaned and synced carbs and put new clutch cable in plus other unrelated things. It idles fine before riding. When I come to a stop itll hang at 3k rpms with the clutch pulled in. If i let the clutch out itll drop back down to 1k. Throttle...

hello guys new member here. I have a 1981 CB750 Custom Cafe Racer Last year the clutch was slipping hard so i knew it was going to need a clutch soon. while moving around in the garage i pressed the clutch and heard a snap!! thinking what ever probably the cable snapped or stretched. than there...

Hey guys! Working on a 1980 F supersport. Just replaced the clutch, and having a problem getting the lifter plate set right. The manual says to "attach plate with 4 bolts and tighten". No torque spec and nothing about how tight against the springs. The 1980 has no notches on the posts for the...

Hey all, new to the forum, just picked up an 82 cb750c last spring and tuning it up for use this summer. I'm checking the valve clearances per the service manual, and exhaust is all nicely between .003" and .005", but intake are all tighter than .0015" (smallest feeler), and I can't use the...

Found an '82 750 Nighthawk that'd been sitting for a few years. Engine turns over, all the lights work, but tank is rusty inside. So I'll clean that out somehow. My concern is the clutch. It's like its stuck. Can't pull it at all. I don't wanna start taking covers off till I have a plan...

Hi! Just opened up the clutch on my K5 to find 7 friction disks and 5 plates. I’m guessing, becuses I don’t seem to be able to find anything anywhere, that there should be 1 less plate than disk. So the question is, has someone been in there before me and left out a plate OR put in an extra...

Has anyone ever fiitted genuine Honda bearings to the clutch basket and not had any play ? I have fitted these twice and the basket still has play.

so i'm new to all this i have recently gotten a 81 cb750 with a sidecar which is why i wanted it it hasn't run in a few years no real history i have gotten it running cleaned the carbs and the tank it really does run well my issue is when taking off in first (yes i'm in 1st) it act like i'm in...

Been having trouble with my 72 and decided to replace clutch, pulled it apart and found the clutch pressure plate is broken :mad:. Any one know were to get one at a reasonable price of have one. Thanks - any suggestions would be appreciated OEM part number 22350-300-010 or 030

Cb 750 1973 I’m having trouble with the second gear on my bike when I shift into second and go hard on the gas it feels like it keeps on coming in and out of gear ,but this is only if I’m going hard on the gas and it only does it on second gear I’ve changed the clutch already but it made no...

Hey all, new to the sight. I have 79 750f with bad clutch rattle, found play in between outer hub and gear. Is this normal?

So my gear shift likes to "hang up" or gets stuck when down shifting, mainly from 2nd to 1st. It's very intermittent. So, as if I'm in 2nd, I try to down shift and it doesn't want to go in 1st, if anything, it wants to go down to neutral, if you try again, doesn't want to go into 1st. Almost...

Anyone tried EBC Clutch friction plates and springs? Did you like them? Any thoughts? Looking into rebuilding my clutch and considering this brand. Any info is greatly appreciated.

Hi guys I'm struggling with my clutch lever as it's too far away and I only have little hands! Does anyone know of any dog legged style levers that would fit the 76 model?

So I have a 1978 cb750k and I notice the clutch doesn't fully engage ( is what it feels like), and when I shift it, I have to almost kick it into gear because if I just lift normally it just grinds. This seems like a clutch issue to me and I saw that the friction plate kits are not crazy...

Looking to install a hydraulic clutch on my 1974 CB750K4 Resto-Mod, has anybody ever done it with any success? I know a new clutch cover will have to be made to mount the slave cylinder too and a new clutch rod. any info would be helpful. Thanks, Dave

Hi all, hope you're all well! After a lot of miles on it, my clutch started slipping under hard acceleration and it looks like friction plates and springs replacement is due. I intend to use OEM friction plates, as I always did. Would you recommend installing stronger clutch springs, like...

I am rebuilding the engine of a 1992 CB750 and came across an odd lock nut when I got to the clutch. It's not a hex nut, it's round with four slots (see photo below). You can only remove it with a special 4-pin socket (OEM part number: 07716-0020203) that Honda is happy to sell you for $60 ...

I recently picked up a CB750K2 that is in near-flawless condition. It was purchased in Italy in 1974 and has had three owners, including me. Together the first two owners put a total of only 311 miles on the bike. Because the bike sat for so long, the second owner had to put thousands into...

Hey everyone, I've been scouring the internet to no avail. I appear to have an oil leak where the "clutch arm actuator" connects to the clutch cover. I have no o ring or washer there, and I'm trying to find out if there should be. Also, if I am missing it how in the world do I put it back on...

My clutch(cb750k5) is basically useless. I'm able to shift up and down without using it. I understand that shifting up isn't a big deal, but downshifting is. I can also go through the gears when the bike is off. I adjusted the clutch just like the manual says. I also have a new clutch cable...

Greetings ya'll, I've read through the majority of threads looking for my particular issue. I'm restoring a 1975 CB750k5 and I currently have an issue with the clutch. Here's what it's doing: With the bike in gear and the clutch engaged there is no slipping = engine and gearbox connected...

Hello to all, Im having a little issue in a 1982 Honda CB750 nighthawk, the bike run great and all of the sudden when i press the clutch and shift to first gear the bike jumps and shuts off as if the clutch is not disengage, I had check everything, cables, basket, adjusted the clutch according...

Hello to all, Im having a little issue in a 1982 Honda CB750 nighthawk, the bike run great and all of the sudden when i press the clutch and shift to first gear the bike jumps and shuts off as if the clutch is not disengage, I had check everything, cables, basket, adjusted the clutch according...

I found the clutch on my 77k was just tossed in and was missing a piece.... :yikes: I need a 25 mm spline washer that is no longer offered from Honda. So please ....where or who how do I get me that washer? Can I use a 1 inch hardware store piece? Rbm

hi. newbe here. i'm rebuilding my 80 cb750f and it runs but is really noisy at idle. i took the clutch apart and noticed that the gear that is riveted to the basket is loose. it rocks back and forth about an eigth of an inch. i have two baskets and they are the same. is this normal? can this be...

Hi all, I am a left leg amputee, who has just started riding again. First day out my leg popped off while shifting, it was a bit scary and had to get some folks to help me. I have since figured out a way to keep my leg on but it is still a bear to shift and was wondering if anyone knows a way...

1993 f2n clutch drags or slips when adjusted have to adjust up so far to get into gear it then slips any comes fault just got bike