Search results

To me it seems like the cable has to go under the wheel to turn the wheel towards the back of the bike. If I try to put the cable over the top then when pulling the throttle cable, it would pull the wheel towards the front of the bike it wouldn't open the throttles in the carbs. With that aside...

Thanks stabler for some sending the pic of the choke. Now I know where that should be hooked up. As for the diagrams, they show the same thing as my repair manual. They just show parts of the carburetor and the throttle but not how they hook up to one another. There is this circular disk in the...

No, I just want to get my bike running. I just don't know how to hook up the cables to the carbs. I would like pictures or diagrams of how to hook them up. I can't find it in my repair manual.

So does that mean I need different right hand controls? (3 cables total including the choke?) Because I currently only have 2 cables. One cable coming from the throttle and one cable from the choke.

Alrighty! I finally got my carbs and I believe they came off a 77 cb750 because its a key top. I currently have a 1976 cb750 but with a 750 nighthawk front end. I am not sure if the cables differ from a nighthawk and 76 cb750. If so then I may have to get different throttle cables to fit the 77...

Thanks! Just bought some 76 carbs. Should be coming in on Wednesday. I hope this does the trick. Since these carbs do not come with any vacuum tubes or fuel lines, how do I find out what tubes go where when I get some? I haven't found any good diagrams that shows tubes going from what to what.

I waaaaaaaaaaaant!

Ok thanks. You've been very helpful. As for my next purchase, do I specifically need a set of carburetors off a cb750 k6? Or are they different models I can search for?

Well that's just great. Lol. Thanks. Do you by any chance know where these carbs would come from?

Here are some pictures: The third picture is of the inside of the carburetor. It seems to me to be pretty clean. I check the main jet and the small jet and they seems to be unclogged. I am unsure if the carburetor is the problem that's preventing my bike from running. Thanks again for all of...

Hey guys. I currently have a cb750 k6 and am doing a carb rebuild. I am beginning to think that the carbs on this bike are not stock. The manufacturer is Keihin and it has VE 75ABW0 with the B boxed in. Do you guys know what these carbs came off of so I can get the correct rebuild kit? I'm...

Flood the motor so I stopped. Should I change out the gas or use a different oil like you did? Im all out of options.

Welp, I replace the stator rotor and the big gear and the good news is that there is no more loud clicking noise. The bad news: it's still not running. Now it sounds like any other bike that won't start. It goes through all the theatrics but it won't run. I have some starter fluid but don't...

Hey, I just got my assembly kit today. I was wondering if I need to drain my oil before removing the stator rotor.

Should I replace the small stater gear while I'm at it or do you think this assembly would do the trick?

The listing says its a 1976 cb750 and I own a 1976 cb750k6. Do you think the stators are the same for that year?

Are you referring to this part? http://www.ebay.com/itm/HONDA-1976-CB750-CB-750-CHARGING-ROTOR-SPROCKET-/380631576110?pt=Motorcycles_Parts_Accessories&hash=item589f68ee2e&vxp=mtr

Would this be what I would need? http://item.mobileweb.ebay.com/viewitem?itemId=151008006410&index=20&nav=SEARCH&nid=21053603631

Hey guys. So I replaced the rollers springs and guides in, put new gaskets and bolts on and filled it with new oil and tried to fire it up last night. When I hit the electric start, it starts to turn over but the loud clicking noise occurs again but not as treacherous as before. Kick starting it...

Got them in! Thanks! Now is there a certain amount of lbs I need to tighten the rotor back on?

Alllllrighty !!! I just got the generator rotor removed. Now how do I install the new rollers, springs and guide pins?

So I took the cover off and now I am having trouble taking the bolt that is attached to the rotor. Every time I a turn it, the rotor turns as well. Is there a special trick to keep the rotor from rotating? Also, I have been doing some research and read that I would also need a rotor puller after...

Thanks. I appreciate the help. I just purchased a starter clutch rebuild kit. http://www.vintagecb750.com/search/?q=starter+clutch I am assuming this should repair the problem?

Hey guys. I am new to this forum and to working on motorcycles so I would appreciate all the help I can get. I purchased a cb760k6 and when trying to electric start the bike, it makes a loud clunking and rattling noise. I looked around other forums and they say it could be the starter clutch...