Results 1 to 10 of 10
  1. #1
    CB750 New Member theredbarn's Avatar
    Join Date
    May 2020
    Location
    Kingston, WA, USA
    Posts
    4

    My son brought home a toy for me to play with...

    I'm going to start riding again! Gave up my last bike after my son was born - 26 yrs later he brings this 79 CB750L home so I can have something to play with! (Mostly because he want's me to ride with him!) Been sitting a lot of it's life, only 4K miles on the odo. I have the Carbs off and am giving them a thorough clean and rebuild. Started and idled but RPMs would not settle if revved. I found 2 of the CV pistons stuck in the closed position. PO was starting to do ready work on it before his Mrs. told him it had to go,(oil change, new tires, forks rebuilt). Lots more to do, I'll be around to ask questions!


    Click image for larger version. 

Name:	IMG_0478m.jpg 
Views:	4 
Size:	312.8 KB 
ID:	9378

  2. #2
    CB750 Guru amc49's Avatar
    Join Date
    Sep 2015
    Location
    Fort Worth TX.
    Posts
    2,909
    SET THE VALVES and usually never done. What makes them scrap. Recognize that most people have to clean the carbs 3 times to get them right. The idle off/idle circuits have a weird seesaw action that makes them problematic. The air cuts do even more and get rid of them. High hanging idle is usually vacuum leak like the forward rubber manifolds. They crack to leak with time and heat.

    The chain tensioner bolts and valve cover bolts strip out easy as spit.

  3. #3
    CB750 Addict Medyo Bastos's Avatar
    Join Date
    Oct 2012
    Location
    Mid South
    Posts
    176
    Geez I was afraid to click on your post! What a great toy!


    Sent from my iPhone using Tapatalk

  4. #4
    CB750 New Member theredbarn's Avatar
    Join Date
    May 2020
    Location
    Kingston, WA, USA
    Posts
    4
    The stuck pistons in the carbs were due to ham fisted-ness of the PO. The main jets in both look like a bent piece of macaroni and the needle jams when they seat. I came across Oldskoolcarbs on the facebook page. I think I may just send them to him and get about cleaning and detailing/ wiring checks etc. on the rest of the bike. I want to get a chain too - no telling how old the one is on there. Could be original equipment for all I know...

  5. #5
    CB750 Guru amc49's Avatar
    Join Date
    Sep 2015
    Location
    Fort Worth TX.
    Posts
    2,909
    The slide pistons match to the caps and if forced they may well be scrap. The slides being delicate as hell. The needles WILL jam if the slide and carb body are not level at install and they are supposed to flop around loose. If you have any contact wear at the bigger top ring-grooved OD of the slides they are probably again junk, they should NEVER touch, they are separated in use by differential air pressure. You absolutely cannot sand on the big OD either, only lower down on the main body that wears to snag sometimes in the lower carb bore.

  6. #6
    CB750 New Member theredbarn's Avatar
    Join Date
    May 2020
    Location
    Kingston, WA, USA
    Posts
    4
    the slide pistons are fine it was the jet holders the needles insert into... check these out.
    Click image for larger version. 

Name:	IMG_0493.jpg 
Views:	6 
Size:	174.9 KB 
ID:	9379

  7. #7
    CB750 Guru amc49's Avatar
    Join Date
    Sep 2015
    Location
    Fort Worth TX.
    Posts
    2,909
    I see one possible wrong part (or three), other than that you are not showing the important parts there. If the needle jet (jet holder) is too tight to stick the needle the needle may be damaged too.

  8. #8
    CB750 New Member theredbarn's Avatar
    Join Date
    May 2020
    Location
    Kingston, WA, USA
    Posts
    4
    The 2 in the middle were bent enough out of shape to grab the needle.

    I have a full kit with new needles coming. What a bitch to order parts. Everywhere I looked asked or a year and model but had the wrong kit! I finally found a reference that showed what years/models got what carbs and was able to order a correct kit by looking for the 81 KC model... Anyway, I'm a weber guy (I do VWs) and have jet measuring tools as well as a set of reams so I'll go through the existing jets and measure reuse as required.

  9. #9
    CB750 Guru amc49's Avatar
    Join Date
    Sep 2015
    Location
    Fort Worth TX.
    Posts
    2,909
    I see the slight bulge on one side now. There is no KC model, it's either a K or a C. For an L I would use K parts. Regardless, all the carbs are closer than the specs seem to show, you can even run 900 carbs, the CV feature allows it. Biggest thing is getting the screw in pilots instead of pressed in.

    One of the parts picced does not seem to have the same hole pattern, roll them around and compare all 4 as to the holes, they must match. If too small a hole for needle it will stick even if straight. That carb type was used in plenty of models with small parts changes everywhere.

  10. #10
    CB750 Guru amc49's Avatar
    Join Date
    Sep 2015
    Location
    Fort Worth TX.
    Posts
    2,909
    Hey, check out the steel piece that installs over the parts there, it can be easily installed upside down to damage a jet holder like that. One end is slightly smaller than the other and the convex end fits against the jet holder.

Similar Threads

  1. Piston to Cylinder Bore Play
    By Wez_ in forum Engine / Exhaust
    Replies: 5
    Last Post: 08-17-2017, 07:28 PM
  2. My new toy
    By snake89 in forum The DOHC Garage (1979-1983)
    Replies: 9
    Last Post: 07-04-2016, 08:28 PM
  3. Front sprocket play? Please help.
    By nsxguy7 in forum Engine / Exhaust
    Replies: 3
    Last Post: 07-02-2016, 10:28 PM
  4. Plug and play mono shock
    By Ridevana in forum The SOHC Garage (1969-1978)
    Replies: 1
    Last Post: 10-23-2014, 07:31 AM
  5. Hello from the home of the groundhog in PA
    By Carman24 in forum The CB750 Garage
    Replies: 4
    Last Post: 12-15-2012, 12:41 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •