Search:

Type: Posts; User: NicksHonda

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    110

    oil/gas mix on the starter cover

    I am not sure where to post this in the forums since I am not sure it is a carb leak.

    I seem to get oil under the carb#2 and all over my starter cover.

    I can only think this is an oil-breather...
  2. Replies
    0
    Views
    90

    Oil or gas on starter cover

    I am finding an oil/gas mix on top of my starter cover.

    Could the oil breather tubes leak around the carbs?
    The breather hoses all check out OK. I have clips on the hoses and T-connections. ...
  3. Welcome from California!

    Welcome from California!
  4. Replies
    1
    Views
    106

    Hello from California!

    Hello from California!
  5. I wouldn't sand blast it. I imagine you won't...

    I wouldn't sand blast it. I imagine you won't get ALL the sand out, but maybe.
    I went with an aftermarket master cylinder. So far so good. I know, it's not original, but mine isn't going to be...
  6. I found these generic ones for $22 on amazon. ...

    I found these generic ones for $22 on amazon. ...
  7. I have heard of people using Pine-sol too. No...

    I have heard of people using Pine-sol too. No experience on it though.
    https://www.youtube.com/watch?v=zDkOgnPidPs
  8. Replies
    1
    Views
    133

    Looks fun!

    Looks fun!
  9. #1 I noticed that the head of the pilot screw for...

    #1 I noticed that the head of the pilot screw for carburetor #1 is raised much higher than the other pilot screws
    Yes this is possible. I had the same thing when I replaced a pilot screw.

    #2 Can...
  10. Replies
    7
    Views
    294

    View Post

    My issue was #2 wasnít running in the lower rpms. It flooded out below 4K. The air cut off circuit will make it run rich when the diaphragm has a tear. Most people apparently plug them as they...
  11. Replies
    13
    Views
    358

    View Post

    The accelerator pump wasnít the problem.

    The #2 air cut off diaphragm was ripped. Apparently the thing to do is block the air cut off valve. I did this and it all works great.

    Iím going to...
  12. Replies
    8
    Views
    296

    Good job! I put a dimmer on mine thinking they...

    Good job!

    I put a dimmer on mine thinking they were too bright. I havenít turned them down or off since the first week I was playing with the dimmer. They are always on now.

    If you havenít...
  13. Replies
    13
    Views
    358

    View Post

    Sooo.

    Iím under the impression the accelerator pump is expected to squirt fuel into all four carburetors, correct?

    This is not happening.

    Iím guessing the fuel rail looking piece...
  14. Replies
    13
    Views
    358

    I check the mic. It was off. I now have .013 mm...

    I check the mic. It was off. I now have .013 mm exhaust on all except #1. #1 is now .010 on both valves exhaust.

    The intake are all .010 except #4 intake is at 013mm.
    I still have a #2 cold...
  15. Replies
    8
    Views
    296

    That's weird that the black is +. The Germans...

    That's weird that the black is +.

    The Germans (Porsche/VW) did that before though. Where brown is negative. Brown is earth, therefore it was ground.

    Your link shows it has red, black and a...
  16. Replies
    8
    Views
    296

    I have those on my BMW. Interesting mounts. Did...

    I have those on my BMW. Interesting mounts. Did you make those?

    It looks like they are on your fork sliders...

    What did you connect them into for power?
  17. Replies
    1
    Views
    223

    Start with the basics. What is your...

    Start with the basics.

    What is your compression on each cylinder?
    What do your plugs look like? When were they last changed?

    While the carbs seem to be problematic and easily get junk in...
  18. Replies
    13
    Views
    358

    I better check my mic. Thanks.

    I better check my mic. Thanks.
  19. Replies
    13
    Views
    358

    I see I used inches to measure the gap in my...

    I see I used inches to measure the gap in my first thread. Sorry about that. I plan to use mm going forward. As such, I can get a .04 mm in all of them. I can not get a .05 mm in any of them.
    ...
  20. Replies
    13
    Views
    358

    View Post

    Ok. So Iím measuring in mm. Youíre telling me to measure in inches by your quote marks. Correct? .04 inches is .10 mm.

    My clymer manual says .08 mm gap. So a wee bit bigger.

    Fun find, my...
  21. Replies
    13
    Views
    358

    They are all tight. I can get my .0015 in all of...

    They are all tight. I can get my .0015 in all of them. I can not get .002 in any of them. Getting the tool tomorrow (hopefully) to get the shims out. I am guessing they are all stock at .280. I...
  22. Replies
    13
    Views
    358

    Under 4K hesitation

    Under 4K whether blipping the throttle or under load it hesitates. After 4K it takes off and runs great.
    Stock 1979 CB750L with 15,442 miles.
    It starts right up from cold with the choke on. After...
  23. Replies
    7
    Views
    294

    I have the same issue. Mine will idle fine. It...

    I have the same issue. Mine will idle fine. It hesitates all around under 4K whether blipping the throttle or under load. After 4K it takes off and seems to run great above 4K.

    I sprayed WD40...
  24. I have a stock hiflow. No issues in the last 150...

    I have a stock hiflow. No issues in the last 150 miles.
  25. I have been looking myself for a '79 Limited. ...

    I have been looking myself for a '79 Limited.
    The short answer is no.

    Long answer:
    From what I can tell, we would need to add the "ears" to mount the caliper. Then you need to check the...
Results 1 to 25 of 35
Page 1 of 2 1 2