Search:

Type: Posts; User: leo750k

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    302

    posting pics of my restoration

    looking for help posting my pics, any advice on file types, file size limits, ........
    tried before without any success. just need some help to get me pointed in the right direction,
    thanks:cool:
  2. Replies
    3
    Views
    204

    Ya I see what you mean, it looks like it will...

    Ya I see what you mean, it looks like it will also be necessary to un-cap the crank bearings too, so it can be lifted up just enough for the seal to clear that groove. I did also see some black...
  3. Replies
    10
    Views
    680

    Sorry I probably have my descriptions wrong, I...

    Sorry I probably have my descriptions wrong, I meant 1 tooth to the small sprocket. But after reading one of your other comments, I will most likely leave it like Honda designed it. This is my first...
  4. Replies
    3
    Views
    204

    1980 CB 750k, rotor side oil seal

    Is the oil seal behind the rotor coil serviceable without removing the motor and splitting the case? And is a minor oil leak/drip in this area detrimental to the coil, stater, or brushes?
    Any info...
  5. Replies
    10
    Views
    680

    I have a 1980 CB-750k and although it does cry...

    I have a 1980 CB-750k and although it does cry for a sixth gear, it is a 5 speed. I have been thinking about increasing the number of teeth on the final drive sprocket by one.
  6. Replies
    3
    Views
    424

    thank you, I will look it over tomorrow. I am...

    thank you, I will look it over tomorrow. I am working on my turn signals. the schematic you sent me shows them having a frame ground. do you know if my 750 has frame grounds on the signals, or wire...
  7. Replies
    3
    Views
    424

    1980 cb750K A, need schematic

    I am trying to work out some issues with my electrical system. I downloaded a manual from this site but the full schematic at the end of the electrical section is not legible. you can see the lines...
  8. Replies
    9
    Views
    1,769

    I purchased an Electrosport Industries rotor from...

    I purchased an Electrosport Industries rotor from Parts Giant, it is testing at about 5.5 ohm. battery is still not charging, I have a voltage reg on its way, stater coil is testing fine, and even...
  9. Replies
    3
    Views
    673

    thanks for the help

    thanks for the help
  10. Replies
    3
    Views
    673

    starter clutch diode/rectifier

    what is the "starter clutch diode/rectifier", and where is it located
    thanks for the help
  11. Replies
    0
    Views
    192

    silicone rectifier

    1980 cb750k, where is the silicone rectifier located? is this part of the voltage regulator or a separate component? manual page 16-2, speaks of it as if its a separate component.
  12. Thread: rotor coil

    by leo750k
    Replies
    1
    Views
    338

    rotor coil

    rotor coil on 1980 cb750k: left or right hand thread on rotor bolt?
  13. Replies
    9
    Views
    1,769

    "whether you think you can, or whether you think...

    "whether you think you can, or whether you think you cant, Your are Right"
    but I dont have any way to balance it, so that is a deal killer. thanks for your input
  14. Replies
    9
    Views
    1,769

    Have you known of anybody that has successfully...

    Have you known of anybody that has successfully rewound one of these coils themselves? doesn't seem that it would be too hard, IF you knew the wire dia,and number of wingdings. I have a good friend...
  15. Replies
    9
    Views
    1,769

    just got done measuring the resistance on the...

    just got done measuring the resistance on the rotor, 1.5 ohms plus or minus a tenth, bad rotor?
  16. Replies
    9
    Views
    1,769

    battery not charging

    Discovered today that my battery is not charging, I have a manual, and haven't started going thru the list yet,
    was wondering if anybody had any advice on what to start with first? I was thinking...
  17. Replies
    4
    Views
    525

    I finally got it out for about a 20-30 min. ride...

    I finally got it out for about a 20-30 min. ride today, temp here is 88 deg. so I know it got fully warmed up, and the idle was more consistent. But I could not get it to run over about 2k rpm, until...
  18. Replies
    4
    Views
    525

    I was reading some of your responses in other...

    I was reading some of your responses in other posts, and am beginning to think I have never really had it completely warmed up. New to air cooled motors, have been scared to let it get to hot just...
  19. Replies
    4
    Views
    525

    cant get a steady idle

    I am now getting ready to do the throttle drop procedure on my 1980 k model. Cant get a steady idle. Using the idle adjusting screw I can get it down to a fairly low rpm, and I think "that doesn't...
  20. my mother always used to say to me "Ya you have...

    my mother always used to say to me "Ya you have Champagne taste, on a beer pocket book"
  21. Replies
    5
    Views
    514

    Ok thanks for the vent and vacuum port info. I...

    Ok thanks for the vent and vacuum port info. I actually did not have to bad a time installing the air-box, boots on box, make sure all tubes and wires were out of the way, then I held the air-box as...
  22. Replies
    5
    Views
    514

    I have a couple questions: the tee between...

    I have a couple questions: the tee between carburetor 2, and 3 that provides vacuum to the alum tube gallery, where does it draw vacuum from? there is a port on the #2
    ...
  23. Replies
    4
    Views
    1,115

    Were you the one that took them apart? Are all...

    Were you the one that took them apart? Are all the parts the same as before disassembly, or are any of them new, or different? if new parts could they possibly be the wrong ones for your model?
    I...
  24. Replies
    5
    Views
    514

    advice for airbox installation

    Well I finally got my air-box boots, any advice on installation is appreciated. My main question is do I attach them to the carbs first and then to the air-box, or vice-versa?
    Thanks for the help...
  25. Replies
    2
    Views
    1,303

    already replaced them with the new pilot screws...

    already replaced them with the new pilot screws that came with my carb kit
Results 1 to 25 of 44
Page 1 of 2 1 2