Search:

Type: Posts; User: amc49

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    2
    Views
    47

    The service manual shows even the first year ones...

    The service manual shows even the first year ones to have some version of the mechanism there, it adjusts the caliper freeplay. Bike on centerstand and weight on back to hold front wheel off ground....
  2. Honda, like all OEMs would have had more than one...

    Honda, like all OEMs would have had more than one parts vendor on assembly line parts, they have them to quickly switch to if the one being used right then begins to have problems. They then jump to...
  3. The Honda idea of the separate primary circuit...

    The Honda idea of the separate primary circuit was to be able to get part/low throttle leaner to better lower emissions and increase gas mileage. When you are at cruise the fuel coming out of the...
  4. Replies
    3
    Views
    76

    https://www.partzilla.com/product/kawasaki/92027-1...

    https://www.partzilla.com/product/kawasaki/92027-1142?gclid=EAIaIQobChMIxr6g9Y2u7QIVFk2GCh1w1gjAEAkYEyABEgIqA_D_BwE

    One of the spacers picced and for a Kawasaki, the Honda will be similar and two...
  5. Replies
    3
    Views
    76

    If the header has the 2 bolt flanges trapped on...

    If the header has the 2 bolt flanges trapped on the pipes then the standard is to use an exhaust gasket and you need the split pieces (two piece exhaust flange thingies) as spacers between the loose...
  6. Just where are you getting them to think you have...

    Just where are you getting them to think you have a choice? It's Honda there and whatever they put in the plastic Honda bags. We lost the better ones when they dropped the 900 and larger bearings...
  7. On a bike with tight motor to open slides fast...

    On a bike with tight motor to open slides fast and a good 4-1 header (early Kerker small primary tube and modded with no glass in it to let the outer can act like atmosphere) and separate pods (K&N)...
  8. It's a miniscule difference and often done for...

    It's a miniscule difference and often done for the difference in exhaust systems using the same engine. May not be the OEM carbset. Thinking the number on left side is supposed to be VB42. My '80F...
  9. Replies
    10
    Views
    3,372

    All mikes easily re-calibrate to zero, what the...

    All mikes easily re-calibrate to zero, what the little wrench with them is for.

    Nobody on earth makes the bearings except Honda and they have this thing about charging more for parts that sit in...
  10. Replies
    10
    Views
    3,372

    People have done it before and gotten away with...

    People have done it before and gotten away with it...............
  11. Replies
    1
    Views
    45

    Hard to say. A small amount may always be there...

    Hard to say. A small amount may always be there but very strong no.
  12. Replies
    6
    Views
    273

    Axle is long enough to hold it as a handle to...

    Axle is long enough to hold it as a handle to keep rotor from striking the floor which will likely ruin it. Use like a 5 lb. baby sledge, I know it sounds like overkill but the best way to get it off...
  13. Replies
    6
    Views
    273

    The axle is better as you have a handle to hold...

    The axle is better as you have a handle to hold the part when it suddenly springs off crank like they usually do. Whatever 'puller' you use gets run up tight to crank and then a sharp rap on the end...
  14. Replies
    6
    Views
    273

    Rotor does indeed have to remove, the crankcase...

    Rotor does indeed have to remove, the crankcase there goes slightly inside the rotor where it has a recess on the back of it. On all early DOHC except possibly the 1100 because that rotor is...
  15. Thread: Which year

    by amc49
    Replies
    2
    Views
    691

    '84-'86 CBX750F

    '84-'86 CBX750F
  16. Replies
    18
    Views
    729

    https://www.denniskirk.com/parts-unlimited/klg-plu...

    https://www.denniskirk.com/parts-unlimited/klg-plug-caps-98.p2068.prd/2068.sku?utm_source=google&utm_medium=csecid=6821162156&aid=76472566741&keyword=830204662494%3A%3Apla-830204662494&kid=83020466249...
  17. Replies
    18
    Views
    729

    What indicates you need to go up on pilot if...

    What indicates you need to go up on pilot if rich? You are at 2 1/2 turns now on air screws, that says pretty rich already if it's not dying. You are adding a lot of air, normal being 1 1/2-2 turns....
  18. Replies
    18
    Views
    729

    There is a ignition mod using GM car parts that...

    There is a ignition mod using GM car parts that some have done..........I had some success with it back in the day. You CANNOT use the GM coils longterm with Honda spark units, they will fail. The...
  19. Replies
    18
    Views
    729

    It makes perfect sense but it is only a...

    It makes perfect sense but it is only a theoretical, meaning it does not have to happen.

    If you have not changed plugs yet that can do every bit of your complaint as it is NOW. Plugs running rich...
  20. Replies
    18
    Views
    729

    If you do not have brand new plugs in then all...

    If you do not have brand new plugs in then all that literally means nothing. Fouled plugs have warped the thinking of thousands of people; they literally trick you with all the ways they can act up. ...
  21. Replies
    18
    Views
    729

    The kill switch will lower the volt to under 12...

    The kill switch will lower the volt to under 12 if a problem.

    If you carefully unscrew the end up inside the plug cap you can replace the resistor above it (like a fuse) with a correct length of...
  22. Replies
    1
    Views
    167

    The pistons can't be seized if you just verified...

    The pistons can't be seized if you just verified they are not.

    '...felt that the piston was moving freely...'

    Similarly, no air in lines if this is true too.....

    'I have good pressure at...
  23. Replies
    18
    Views
    729

    Who supplied the carbs/intakes? No trouble...

    Who supplied the carbs/intakes?

    No trouble likely with harness, if you have 12 volts at the coils + (black/white) you are as good as you will get. The kill switches themselves can make for low...
  24. Replies
    18
    Views
    729

    If you truly have 150 psi then it is not the...

    If you truly have 150 psi then it is not the valves.
  25. Years old info, company likely dead. Engine...

    Years old info, company likely dead.

    Engine fogging oil like boats use will work but dirties the plugs up.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4