Search:

Type: Posts; User: amc49

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds; generated 39 minute(s) ago.

  1. Replies
    4
    Views
    223

    If that aluminum shield is simply snapped into...

    If that aluminum shield is simply snapped into the box bottom and it gets loose to touch the positive post you'll have great fun and maybe even a fire.
  2. FYI, you can 'fully charge' a battery and it...

    FYI, you can 'fully charge' a battery and it still be deader than a doornail..............
  3. Replies
    7
    Views
    1,653

    ???? No rocket science there.......... Bike on...

    ???? No rocket science there..........

    Bike on centerstand and rear tire slightly off ground. Remove ONE top shock bolt only, the other side shock will still support the wheel and arm but it will...
  4. Replies
    10
    Views
    219

    You gotta read..................service manual...

    You gotta read..................service manual page 8-4 and 8-6. All clearly called out and the reason why is built into where they go, and for quick ID of parts without measuring them or looking...
  5. Thread: New owner

    by amc49
    Replies
    1
    Views
    44

    Go to partzilla.com and plug the bike in for...

    Go to partzilla.com and plug the bike in for picced parts lists, that may help too.
  6. In any fashion that gets the part tight while...

    In any fashion that gets the part tight while still being pretty close to the original location of pin/slot. Provided you haven't messed up the advance unit swing to have it come apart. Holding the...
  7. Replies
    7
    Views
    1,653

    https://moto-odejda.ru/file/HondaNithawk.pdf ...

    https://moto-odejda.ru/file/HondaNithawk.pdf

    Page 2-4.

    Seat has to come off first.
  8. Replies
    2
    Views
    104

    New (to owner) bike, may not even have the spark...

    New (to owner) bike, may not even have the spark units..........sold to somebody else. They bolt down over the top of battery.
  9. Replies
    5
    Views
    197

    The starter clutches are well known for rattling,...

    The starter clutches are well known for rattling, they commonly loosen at the 3 bolts holding the housing together. Loctite to cure. Problems can be past that though, the 3 roller setup just sucks...
  10. Thread: Carb interchange

    by amc49
    Replies
    1
    Views
    80

    Any 750 DOHC from '79-'83 will work, '81 and...

    Any 750 DOHC from '79-'83 will work, '81 and later better because of screw in pilots instead of pressed in. Any model, C, K, F, SC, L.
  11. Replies
    16
    Views
    531

    'you're referring to the part of the slide that...

    'you're referring to the part of the slide that has the notch down the side that inserts into the carb bore and not the thicker bit that inserts into the top cap?'

    Yes. Don't touch the bigger...
  12. Replies
    16
    Views
    531

    Possibly but possibly indirect. The pressing on...

    Possibly but possibly indirect. The pressing on the sync tabs says you have enough flow past butterflies to coax the slides into trying to float up. They are open too much at least on one if that...
  13. Thread: newbie here

    by amc49
    Replies
    6
    Views
    290

    A CBX sitting in office likely denotes a big time...

    A CBX sitting in office likely denotes a big time seller with $ signs for eyes. Why he wanted so much, willing to let it rust before losing a cent of highly inflated value. He probably wanted 10K for...
  14. Replies
    10
    Views
    219

    Or dremel with a small say carbide tip or like a...

    Or dremel with a small say carbide tip or like a chainsaw chain sharpening rock, going to make a mess and the particles need to be kept contained. They will eat the motor.

    The idea is to eat up...
  15. Replies
    16
    Views
    531

    Yes, the actual CV slide and top cover on carb. ...

    Yes, the actual CV slide and top cover on carb.

    That design is the least efficient CV type as it leaks unlike rubber diaphragm ones but the leak is calibrated by the clearance between the big OD...
  16. Replies
    10
    Views
    219

    Service manual and page 8-5. ...

    Service manual and page 8-5.

    https://moto-odejda.ru/file/HondaNithawk.pdf

    Note the first words to UNSTAKE the nut FIRST. Look for a punchmark staking the nut down, if you remove the nut the...
  17. Replies
    16
    Views
    531

    The 'fine wire' can be no thicker than 'E' string...

    The 'fine wire' can be no thicker than 'E' string on a guitar or thinnest one and .013" in diameter. The mixture screws should each affect the idle, you should be able to kill that cylinder going...
  18. Replies
    16
    Views
    531

    double post

    double post
  19. Thread: newbie here

    by amc49
    Replies
    6
    Views
    290

    There you go, that man I'll follow.

    There you go, that man I'll follow.
  20. Thread: newbie here

    by amc49
    Replies
    6
    Views
    290

    Do as you will but here we don't give even that...

    Do as you will but here we don't give even that for something not running. I know I wouldn't and don't care how collectible it is. At the asking price it needs to be running and well.

    The not...
  21. Replies
    10
    Views
    219

    If you are talking about the one with 4 notches...

    If you are talking about the one with 4 notches in it yes.
  22. Thread: Clutch issue

    by amc49
    Replies
    4
    Views
    297

    Answer still the same.............if the clutch...

    Answer still the same.............if the clutch stack height is not correct it can do that. It would take a thick book to cover all the other ways somebody can mess those up. Especially after 10-15...
  23. Replies
    5
    Views
    197

    Get down low and check out the bottom of it, the...

    Get down low and check out the bottom of it, the plastic simply snaps in place and if it comes loose the terminal plate then comes loose to not connect wires. It's an instant stop if it happens, my...
  24. Replies
    5
    Views
    197

    The only way I could imagine all that would be if...

    The only way I could imagine all that would be if the alternator stator or something close came loose and it should have blown the main fuse.

    I would remove alt cover anyway to slowly turn the...
  25. Replies
    16
    Views
    531

    '....I'm not too concerned about the number since...

    '....I'm not too concerned about the number since as all four read the same.'

    What are the odds of that? The same as all 4 leaking valves the same amount. Pretty rare and screams gauge is trash....
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4