Search:

Type: Posts; User: dirtdigger

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    2
    Views
    89

    black was not available till 77 only colors in...

    black was not available till 77 only colors in 73 was sunrise orange, a candy olive and metallic brown. 4 into 1 was not stock for 73 non of the k bikes had anything but 4 pipes.
  2. Replies
    20
    Views
    2,039

    I couldnt tell you. Go to some online honda...

    I couldnt tell you. Go to some online honda parts places and look up the part numbers and compare, that would be your most accurate way of finding out.
  3. Replies
    20
    Views
    2,039

    If it has chunks missing its junk...the material...

    If it has chunks missing its junk...the material has gotten hard and brittle from the years of being in hot oil and just the general engine heat. Some wear marks are not bad as long as the surface...
  4. Replies
    20
    Views
    2,039

    The DOHC doesnt have near the following that the...

    The DOHC doesnt have near the following that the sohc motor does. I am sure at some point CycleX will probably offer rebuilt tensioners with their new tensioner material. Doubt many other companies...
  5. Replies
    2
    Views
    126

    Could have been just upgraded performance pads. ...

    Could have been just upgraded performance pads. Could have been sitting for couple years and things got rusty and stuck so he replaced them. Bike pads are thin to start with so maybe he thought...
  6. Replies
    6
    Views
    220

    So have you tried to install the new clutch? ...

    So have you tried to install the new clutch? Just install per the instructions and run it. The number of plates in the stack may differ from brand to brand.
  7. Replies
    6
    Views
    220

    I really need some pictures. are there actually...

    I really need some pictures. are there actually two disks in the center or is it the cushion disk that has come apart? Sounds to me like it has some sort of aftermarket clutch in it because there...
  8. Replies
    6
    Views
    220

    Could be an aftermarket setup. Does the clutch...

    Could be an aftermarket setup. Does the clutch work? If it does run it. Post a couple pictures of the clutch stack.
  9. Replies
    4
    Views
    161

    for a stock street motor I would just use stock...

    for a stock street motor I would just use stock rods and maybe put new rod bolts in them. The Cycle x rods are the cheapest aftermarket rods you will find, if you cant afford them then just use the...
  10. Replies
    9
    Views
    169

    Just my thoughts, not sure if it makes much...

    Just my thoughts, not sure if it makes much difference :laugh:
  11. Replies
    9
    Views
    169

    You can do that. The only reason I do not like...

    You can do that. The only reason I do not like to flip them over is so any debri that is in the engine stays where it is as it was in the bike, if there is an issue internally the debris and the...
  12. Replies
    9
    Views
    169

    You can screw some strategically placed blocks to...

    You can screw some strategically placed blocks to the pallet that keep the motor from moving around then use some ratcheting straps to hold it down to the pallet. Or if your handy you could make...
  13. Replies
    4
    Views
    161

    What is your intent for this engine? Street...

    What is your intent for this engine? Street motor? road race? drag race? If it is a street motor I really do not recommend aluminum rods. They will require clearancing, how much will have to be...
  14. Replies
    3
    Views
    119

    If it is a recent rebuild and it smokes since...

    If it is a recent rebuild and it smokes since then my guess would be oil ring got rolled when dropping the cylinders on or there was improper crosshatch in the cylinders when rebuilt...or maybe just...
  15. Thread: BAM!

    by dirtdigger
    Replies
    6
    Views
    189

    Thats why I was asking because my name is Dana lol

    Thats why I was asking because my name is Dana lol
  16. Thread: BAM!

    by dirtdigger
    Replies
    6
    Views
    189

    Did I miss something? What Dana you talking...

    Did I miss something? What Dana you talking about?
  17. Replies
    6
    Views
    334

    I know some guys using these parts in racing...

    I know some guys using these parts in racing motors and as far as I know they are working. I am still using oem rubber wheels with no issues. If your building a race motor they may be the way to go...
  18. Replies
    7
    Views
    469

    Hope the rocker arms got mark for the correct...

    Hope the rocker arms got mark for the correct position on the camshaft, risk ruining the cam and the rockers if put back in the wrong place as they wear to each other.
  19. Replies
    6
    Views
    334

    Kens a good guy and will help you get set up with...

    Kens a good guy and will help you get set up with the right stuff.
  20. Replies
    3
    Views
    189

    cyclex has them for the earlier bikes, may call...

    cyclex has them for the earlier bikes, may call them to see what they can do. Other then that do a google search found quite a few hits for over length cb750 throttle cables.
  21. Replies
    3
    Views
    189

    Stock rods are fine. They are not torque to...

    Stock rods are fine. They are not torque to yield but is always a good practice to replace rod bolts. Unless you have kept track of the stretch from new you have no idea how close they are to...
  22. Replies
    3
    Views
    189

    Take apart the other motors and see what you got....

    Take apart the other motors and see what you got. The crank is junk, it will cost more to repair then what you could buy a used one for off of ebay but you have other engine so no real point in...
  23. Replies
    2
    Views
    169

    Im slightly confused...What engine tag are you...

    Im slightly confused...What engine tag are you looking for? The number you posted above is the engine number. Which is a K1 or a 1971
  24. Replies
    6
    Views
    334

    There have been some issues with the crusinimage...

    There have been some issues with the crusinimage pistons having inconsistent piston dome heights, if you go that way be sure to measure and mock up everything so you can calculate compression. ...
  25. Yup serial number shows early 75.

    Yup serial number shows early 75.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4