Search:

Type: Posts; User: dirtdigger

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. The sohc bikes run fine with pods, not an issue...

    The sohc bikes run fine with pods, not an issue just appropriate jetting...easy to do.
  2. The pinging noise is probably too much starting...

    The pinging noise is probably too much starting fluid, not really the best thing for an engine, but anyway. Open up all the carbs and blow threw the jets and emulsion tubes. Make sure floats are...
  3. Replies
    17
    Views
    5,244

    OK thats a DOHC motor, I would suggest posting in...

    OK thats a DOHC motor, I would suggest posting in the DOHC section as this is the SOHC section
  4. Replies
    17
    Views
    5,244

    There was no vin in this post for anyone to tell...

    There was no vin in this post for anyone to tell you what your engine is....

    Remember, this is all voluntary, people come on and help when they have time. Sometimes you gotta give it a couple...
  5. Replies
    17
    Views
    5,244

    This post is 5 years old. Please start a new post...

    This post is 5 years old. Please start a new post with your vin and the information you are looking for.
  6. I'll give it a shot.

    I'll give it a shot.
  7. Replies
    4
    Views
    195

    no problem

    no problem
  8. Replies
    9
    Views
    406

    You need to be able to tip the carbs up side down...

    You need to be able to tip the carbs up side down so you can adjust them/set float level
  9. Replies
    4
    Views
    195

    Yes they all should close. Look on the linkages...

    Yes they all should close. Look on the linkages connecting the chokes...they are threaded for adjustment.
  10. Replies
    2
    Views
    210

    Depends on what year of f top end the75,76 should...

    Depends on what year of f top end the75,76 should be same outside diameter but the 77,78f2 top end have larger diameter spigots and use bigger boots...they also used the keyhole carbs that are larger...
  11. Replies
    2
    Views
    218

    Actually altitude is a big effect of fuel ratios....

    Actually altitude is a big effect of fuel ratios. Sea level will require more fuel then higher elevations. Humidity also contributes to fuel mixture, maybe not as much as temperature and elevation...
  12. Replies
    9
    Views
    406

    yes, engines and carbs are basically the same...

    yes, engines and carbs are basically the same regardless.
  13. Replies
    9
    Views
    406

    It says 72 cb750

    It says 72 cb750
  14. Replies
    3
    Views
    212

    oil line? if there is a hose on the top of the...

    oil line? if there is a hose on the top of the forks is an air line used for adjusting air pressure in the forks.
  15. Replies
    2
    Views
    194

    black was not available till 77 only colors in...

    black was not available till 77 only colors in 73 was sunrise orange, a candy olive and metallic brown. 4 into 1 was not stock for 73 non of the k bikes had anything but 4 pipes.
  16. Replies
    20
    Views
    2,322

    I couldnt tell you. Go to some online honda...

    I couldnt tell you. Go to some online honda parts places and look up the part numbers and compare, that would be your most accurate way of finding out.
  17. Replies
    20
    Views
    2,322

    If it has chunks missing its junk...the material...

    If it has chunks missing its junk...the material has gotten hard and brittle from the years of being in hot oil and just the general engine heat. Some wear marks are not bad as long as the surface...
  18. Replies
    20
    Views
    2,322

    The DOHC doesnt have near the following that the...

    The DOHC doesnt have near the following that the sohc motor does. I am sure at some point CycleX will probably offer rebuilt tensioners with their new tensioner material. Doubt many other companies...
  19. Replies
    2
    Views
    222

    Could have been just upgraded performance pads. ...

    Could have been just upgraded performance pads. Could have been sitting for couple years and things got rusty and stuck so he replaced them. Bike pads are thin to start with so maybe he thought...
  20. Replies
    6
    Views
    411

    So have you tried to install the new clutch? ...

    So have you tried to install the new clutch? Just install per the instructions and run it. The number of plates in the stack may differ from brand to brand.
  21. Replies
    6
    Views
    411

    I really need some pictures. are there actually...

    I really need some pictures. are there actually two disks in the center or is it the cushion disk that has come apart? Sounds to me like it has some sort of aftermarket clutch in it because there...
  22. Replies
    6
    Views
    411

    Could be an aftermarket setup. Does the clutch...

    Could be an aftermarket setup. Does the clutch work? If it does run it. Post a couple pictures of the clutch stack.
  23. Replies
    4
    Views
    283

    for a stock street motor I would just use stock...

    for a stock street motor I would just use stock rods and maybe put new rod bolts in them. The Cycle x rods are the cheapest aftermarket rods you will find, if you cant afford them then just use the...
  24. Replies
    9
    Views
    253

    Just my thoughts, not sure if it makes much...

    Just my thoughts, not sure if it makes much difference :laugh:
  25. Replies
    9
    Views
    253

    You can do that. The only reason I do not like...

    You can do that. The only reason I do not like to flip them over is so any debri that is in the engine stays where it is as it was in the bike, if there is an issue internally the debris and the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4